XGSM Iași — Service & Piese GSM

First aid

Phone won't turn on: the steps, in order

A black, silent phone does not necessarily mean a dead phone — most of the time it is a fully drained battery or a freeze that a force restart fixes. Below are the steps in the right order: charging first, then the button combo for your brand, then the screen test. And your photos usually stay put even when the phone shows no sign of life.
Anyone can do it40 minAndroidSamsungXiaomiHuaweiMotorolaGoogle PixelOnePlusOppoiPhoneChecked: November 17, 2026

Short version

  • Put it on charge for 30 minutes with a cable and charger you know work — a dead battery shows nothing at first.
  • Then do the force restart for your brand: Samsung = side + Volume down over 7 s, iPhone = Volume up, Volume down, then hold the side button.
  • Still black? Call it from another phone — if it rings or vibrates, only the screen is dead.
  • Don't heat it, don't open it and don't charge it if it was in water or the battery is swollen.
  • Your photos usually stay on the phone — tell the technician your data matters before any work starts.

Step 1: leave it on charge for 30 minutes

A phone with a completely flat battery looks exactly like a dead one: black screen, no vibration, no sound. Samsung's own help page says that in most cases a phone that won't turn on didn't charge properly — and Google warns that a fully drained Pixel can show nothing on screen for up to 25 minutes after you plug it in. That's why step one is always charging, not buttons.

Warning· Was it in water, or is it still wet?

Don't charge it at all — current plus water means short circuits on the board. Let it dry and read what to do with a wet phone. Same if the battery is swollen (bulging cover, screen pushed outwards): no charging, no pressing — straight to a shop.
  1. Get a charger and cable you know work

    Use a cable and adapter that charge another phone without issues — dead cables and adapters are the most common cause of “it won't charge”. Samsung adds that an incompatible charger can even damage the phone, so use the original or a certified one.

    Phone
    Charger
    Outlet

    Connection: Phone via USB-C → Charger. Charger via power → Outlet.

  2. Plug it in and leave it alone for 30 minutes

    Push the cable fully into the port — it shouldn't wiggle — then leave the phone alone. A fully drained battery needs a few minutes of charge before anything shows on screen, and Apple recommends leaving the iPhone on charge for a full hour before trying again. Resist the urge to press buttons every five minutes.

  3. Check the outlet, the port and the case

    Plug something else into the same outlet — a lamp, for instance — to make sure it works. Look inside the phone's port for dust, lint or bent pins, the check both Google and Samsung recommend. Take the case off too if it presses on the buttons or stops the cable from seating fully.

    Lint in the port comes out with a wooden or plastic pick — never with anything metal.

Phone screen: Empty battery

The empty battery icon is a good sign: the phone is off and charging. Let it gather charge before you try turning it on.
  • The empty battery icon or a charge percentage on screen — the phone is alive, just flat;
  • a blinking LED — on some Xiaomi models it's red when the battery is very low;
  • a short vibration or a charging sound when you plug in the cable;
  • the back warms up slightly — careful: warm is normal, hot is a bad sign;
  • nothing at all — still normal within the first 20–30 minutes, according to Google.
  1. Minutes 0–30

    On charge, with a cable and charger you know work. Hands off.

  2. After 30 minutes

    The force restart for your brand, with the cable still connected.

  3. Then

    The screen test: call it, feel for a vibration, plug it into a computer.

  4. After ~1 hour with no reaction

    Nothing on screen, no LED, no sound? Most likely a repair-shop job — see the table below.

Step 2: the force restart for your brand

After the 30 minutes on charge — with the cable still connected — comes the force restart. It cuts power to the board and bypasses a frozen system without touching your photos or messages; Samsung confirms that, done right, it erases nothing. The combos are the same ones as in our full force-restart guide, checked against the makers' own support pages.

  1. iPhone 8 or newer, X and SE (2nd–3rd gen)

    Press and quickly release Volume up, then Volume down. Then hold the side button until the Apple logo appears — this can take more than 10 seconds, so don't stop if the power-off slider shows up in the meantime.

    1. 1Press and releaseVolume up
    2. 2Press and releaseVolume down
    3. 3Hold until the apple showsSide button10 s

    Press the phone's physical buttons in the numbered order. 1. Press and release (Volume up). 2. Press and release (Volume down). 3. Hold until the apple shows (Side button, 10 s)

  2. iPhone 7 and iPhone 7 Plus

    Hold the side button and Volume down at the same time until the Apple logo shows — this can also take more than 10 seconds.

    1. 1Hold both until the apple showsSide buttonVolume down10 s

    Press the phone's physical buttons in the numbered order. 1. Hold both until the apple shows (Side button + Volume down, 10 s)

  3. iPhone 6s, 6s Plus and SE (1st gen)

    Hold the Sleep/Wake button and the Home button at the same time until the apple shows — about 10 seconds.

    On iPhone SE (1st gen) the Sleep/Wake button is on the top edge.

    1. 1Hold both until the apple showsSide buttonHome10 s

    Press the phone's physical buttons in the numbered order. 1. Hold both until the apple shows (Side button + Home, 10 s)

On the other brands the combos are the same ones as in the force-restart guide:

  • Huawei and Honor: Power for 10–15 seconds; on models running EMUI 11 or newer (such as Mate 40 or P50), hold Power + Volume down for over 10 seconds.
  • Motorola: Power for 10–20 seconds — up to 30 on some newer models.
  • OnePlus, Oppo and Realme: Power + Volume up for about 10 seconds, then turn it on normally.

Tip

Hold the buttons for the full time shown — a frozen or fully drained phone responds more slowly. Count the seconds out loud and only let go when you see the maker's logo or feel the restart vibration.

Note· Ended up in a menu in English?

On some Samsung phones the combo opens the “maintenance boot mode” (Maintenance Boot Mode). Pick Normal boot with the volume keys and confirm with the side button — and don't touch anything with “reset” or “wipe” in the name, those erase the phone.

Step 3: maybe only the screen is dead

A phone can be perfectly alive with a dead screen — a classic case after a drop or a failed display. Huawei's own help page says it plainly: if the phone rings or vibrates while starting but the screen stays black, the screen is most likely faulty. Here's how to check:

  1. Call it from another phone

    Call your own number from another phone or ask someone to ring you. If your phone rings or vibrates while its screen stays black, the phone is alive — the problem is the screen only. Google suggests the same test on Pixel, optionally triggered from the Find Hub app.

  2. Feel for the vibration and look at the screen closely

    Redo the force restart with your palm on the phone: a short buzz means it restarts, so only the screen stopped showing things. Then look at the screen very closely under strong light — Google recommends looking for any image at all, however faint: a screen with a dead backlight can still show a pale image.

  3. Plug it into a computer

    Connect it to a laptop or PC with a data cable: if the computer plays a connection sound or lists it as a device (in Finder or iTunes for an iPhone), the phone works. An iPhone stuck in recovery mode shows the cable-to-computer drawing on screen — you get out of it with a force restart, details in the recovery and DFU guide.

    Phone
    Laptop or PC

    Connection: Phone via data cable → Laptop or PC.

Note· It rings or vibrates, but the screen is black?

Good news: your data usually stays put, and a new screen usually fixes everything. More in black screen but the phone works and getting photos off a phone with a dead screen.

Step 4: what happened before it died

A phone rarely dies for no reason. What happened before is the best clue to the cause — go through the list below and note what fits:

  • It fell in water or got wet — don't charge it at all: corrosion can kill the board in the following days. Read phone in water: the first 10 minutes.
  • It was dropped or hit — a flex cable popped off its socket, a screen cracked on the inside or a board crack can mean exactly this; it's usually a repair-shop job.
  • It sat on the logo or died during an update — that sounds like a software error, not hardware. See phone stuck on the logo.
  • The battery lasted less and less, or it died at 20–30% — a worn battery: the phone no longer has the power to start even though it showed a percentage. See when replacing the battery is worth it.
  • It sat in extreme cold or heat — Huawei warns that a phone that is too cold or too hot may refuse to power on or charge. Let it return to room temperature, then try again.
  • You changed the charger or cable recently — a wrong accessory may not charge it at all. Go back to the charger and cable the phone came with.

Tip· Write the history down

“It fell yesterday”, “it was at 30% and died suddenly”, “it heated up while charging” — a technician finds the cause far quicker if you give them the full history, not just the phone.

From symptom to cause to what a shop does

After the steps above you can already make a rough diagnosis. The table links each symptom to the usual cause and to what a repair shop typically does about it:

Symptom → likely cause → the usual repair
What you see or what happensLikely causeWhat the shop does
Nothing, even after an hour on a known-good chargerDead battery, faulty port or a mainboard problemMeasures the draw on a bench power supply and tries a test battery; then replaces the port or battery, or repairs the board
It rings or vibrates, but the screen is blackFaulty screen, or its flex popped out of the socketFits a test screen and, if confirmed, replaces the display
Starts only on the charger, dies when you unplugWorn battery that can no longer hold a chargeReplaces the battery — usually a straightforward repair
Starts but sits on the logo or keeps restartingSoftware error or full storageReinstalls the system, keeping the data wherever possible
Died after water or dampCorrosion or a short on the boardChemical or ultrasonic cleaning, then a component-level diagnostic
Died after a dropFlex off its socket, internally cracked screen or a board crackOpens it, reseats the flexes and tests the parts one by one
Gets unusually hot when you plug it inShort circuit on the board or a faulty batteryCuts the power and traces the component that heats up
The power button no longer clicks or is stuck insideFaulty button or power flexReplaces the button or the flex; can power the phone on without it

A serious shop always starts with a diagnostic: the bench power supply shows within seconds whether the board draws current or is dead entirely, and a test battery and screen rule out the most common causes without touching your data.

The photos and data on it

The natural question: “are my photos gone?” Most of the time, no. Photos and messages live on the memory chip and are not erased when the battery dies or the screen breaks — a “dead” phone usually keeps its data intact. What can actually destroy it: a factory reset, water combined with current, or the wrong intervention.

  • Say your data matters from the start — before any repair or test. Some board-level work or reinstalls can require a wipe, and the technician picks a different route when they know the photos are the priority. See how data recovery works.
  • Don't factory-reset to force a start — Wipe data or Factory reset in service menus erases everything, irreversibly.
  • If it starts, back up right away — before anything else: full backup on Android or iPhone backup.
  • Dead screen, live phone — the data is usually readable after a screen replacement or through an external display: getting photos off a phone with a broken screen.

Warning· The phone won't start at all, but the photos matter?

Recovery from a phone that won't turn on is bench work, with dedicated tools — not a home job. Every risky attempt (opening it, odd chargers, menus with “wipe”) can make things worse, so stop at the steps in this guide.

What not to try

Just as important as the steps above are the things that sound like good ideas and aren't:

Do

  • Use a charger and cable tested on another phone.
  • Give it enough time on charge — a dead battery needs it.
  • Hold the button combos for the full time shown — up to 60 seconds on some phones.
  • Note what the phone does at each step: vibration, LED, sound, nothing.

Don't

  • Don't heat it with a hair dryer, a radiator or in the sun — heat degrades batteries and can be dangerous.
  • Don't put it in the freezer — the cold myth brings condensation onto the board and can kill the phone.
  • Don't open it at home — the small flexes and screws are fragile and you may lose the warranty.
  • Don't poke pins or other metal objects into the port — you scratch and bend the pins; lint comes out with wood or plastic only.
  • Don't charge it if it was in water, is hot, or has a swollen battery.
  • Don't buy “miracle chargers” or use dubious power sources — an incompatible charger can damage the phone, Samsung warns.

Danger· Swollen battery or hot phone

Bulging cover, screen pushed outwards, a strange smell, or a phone that heats up badly on charge? Stop charging it, don't squeeze it and don't press on the battery — a swollen battery can catch fire. Put it on a non-flammable surface and take it to a shop. Details: hot phone and swollen battery.

When it's a repair-shop job

You charged it for 30–60 minutes, did the force restart for your brand, ran the screen test — and still nothing? Then it's almost certainly a hardware problem. It's a repair-shop job even earlier when:

  • the phone heats up abnormally when you plug it in — stop charging it right away;
  • it was in water or other liquids — corrosion keeps working even when the outside looks dry;
  • it took a drop and now shows no sign at all;
  • it starts but never gets past the logo or dies right away — see also phone stuck on the logo;
  • it rings or vibrates but the screen is black — a screen replacement is usually the fix.

A bench diagnostic quickly shows whether it's the battery, the port, the screen or the board — see the service page or ask for a quote. If your phone's menus or screen look different from this guide, write to us from the box at the end of the page.

Frequently asked questions

Why won't my phone turn on even though it charged all night?
If it sat on a dead cable or a dead charger, it never actually got power. Try a different cable, charger and outlet, give it 30 minutes, then do the force restart. If it still shows nothing, the battery or the port may be at fault — the likely causes are in the table above.
The phone vibrates or rings, but the screen is completely black. What is it?
Almost certainly a faulty screen — the phone starts and works, it just can't display anything. Huawei confirms this exact sign as pointing to a dead screen. Your data normally stays put and a new screen usually fixes everything — see black screen on a working phone.
Do I lose my photos if the phone won't turn on?
Most of the time no — photos live on the memory chip and don't vanish with the battery or the screen. Just avoid a factory reset and tell the technician your data matters before any operation; recovery from dead phones exists — see the data recovery page.
How long does a fully drained phone need on charge before it starts?
At least 15–30 minutes: Xiaomi says 15–30, Samsung says “at least a few minutes”, and Apple recommends a full hour before trying again. Google warns that a dead Pixel may show nothing for up to 25 minutes after plugging in. Give it half an hour before drawing conclusions.
The phone won't turn on after falling in water. Can it still be saved?
Possibly — but don't charge it and don't power it on: current plus water destroys the board. Let it dry fully, at least a day, then take it to a shop for corrosion cleaning. Data is often saved even from phones that never start again — details in the water damage guide.
It only starts while on the charger and dies the moment I unplug. Why?
The battery can no longer hold any charge — the phone lives off the charger alone. That's the classic sign of a worn or dead battery, and the fix is replacing it, not the phone. See when a battery replacement is worth it.
I charged it, force-restarted it, called it — nothing works. What next?
It's a repair-shop job: the cause is most likely hardware — battery, port or board. A bench test shows the faulty part quickly, and if photos matter, say so from the start. Until then, don't insist with odd chargers and don't open it.

Does your phone look different, or is something missing here?

Menus and buttons differ from model to model and change with updates. If these steps do not match your phone or you cannot find what you need, tell us your model and what you see on the screen: we will answer you and update the guide.

Checked against

Still no sign of life?

Bring it in for a diagnostic — on the bench we can quickly tell whether it's the battery, the port, the screen or the board, and [data can be recovered](/recuperare-date) even from phones that no longer start.